Menu
Cart 0
57004 - '09-18 Jeep Wrangler JK Trail Rocker Overhead (W/Auto Dimming Mirror)

57004 - '09-18 Jeep Wrangler JK Trail Rocker Overhead (W/Auto Dimming Mirror)

  • $574.99


 

Your only weather resistant option for controlling up to 8 accessories on your JK Jeep! This kit mounts 6 LED switches overhead using existing mounting holes. The power center includes a bolt-on bracket to mount under the hood with 200 amps of fused protection. Easily installed with our detailed instructions and plug-n-play design. All high quality TXL output wiring is included, allowing you to avoid the inferior wire provided with some accessories. This kit includes a custom CNC braket to lower the rear view mirror down about 3/4" to allow for clearance of the switch panel. 

  • Control up to 8 accessories, (8) 30 amp fuses and (8) 30 amp relays.
  • Weather resistant housing around the power center and connections.
  • Custom bolt-on powder coated bracket for the power center and switch panel.
  • Switch panel mounts 6 weatherproof LED switches in an overhead location.

Note: 57004 is for use with Auto Dimming Mirror only. Please see 57003 for use with Non-Auto Dimming Mirror. Jeep breaks down the models as follows:

Generally With Auto Dimming:

  • Rubicon 
  • 75th Anniversary
  • Willys Wheeler W
  • Sahara
  • Sport S

​Generally Without Auto Dimming:

  • Sport
  • Willys Wheeler 

Winch Ready! The Trail Rocker system includes dedicated wires for controlling a winch. Purchase of our Winch Control Add-on Kit part number 57150 is required for operation. 

The heart of the Trail Rocker is the fuse & relay center. Here you will find eight 30 amp fuses and eight 30 amp relays. While the switch panel only comes with six total switches, we provide you with the two extra circuits for doubling up on dual high amp systems. Say for example, two 20 amp lights powered off of two relays but only one switch. 

The top of the weatherproof fuse & relay center features the stylish logo silkscreened onto it. Along with the fused power source mounted next to it.  

The 200 Amp MIDI fuse comes pre-installed and prewired. There’s no worrying about how to crimp that 6 gauge power cable. 

The underside of the fuse & relay cover has a built in gasket to help keep any moisture out and to act as an extra support for the relays. This extra support on the relays ensures that no matter how good or bad you are on the trails, the relays will not pop out of place. 

Attention to detail shows in this bolt with O-ring combo to hold the top cover on.  

Underneath the fuse & relay center you will find the powder coated custom mounting bracket with stainless hardware. This bracket is designed to install in existing mounting holes under the hood. 

 

This harness attaches the fuse & relay center to the switch panel. It’s a plug-n-play design that only requires you to route it and plug it in.  

Exiting the fuse & relay center we provide you with 21’ of wire to reach any 12 volt accessory you have.

Printed every 12” on the wire you’ll find the circuit description, a signature touch of ours. 

The parts kit comes with everything you’ll need to install the Trail Rocker, except the tools and the Jeep.

You’ll also find a custom pigtail that allows the Trail Rocker to power up only when the key is turned on. The system is shipped to be powered at all times. 

You'll also find a winch pigtail that is pre wired into the kit. This pigtrail is ready to wire up to your winch. The other end is ran up to the switch panel. With the purchase of our custom winch switch PN 57150. You can easily replace one of your switches and control your winch from in the cab. Be sure to visit our wiring schematics page for details on wiring this to your winch. www.painlessperformance.com/schematics

If you’ve never seen a Painless manual, you’re in for a treat. Scroll to the top for a PDF version of this nearly 50 page full color manual. You’ll wish we made manuals for everyday living. 

 

Here is the complete kit.  Everything you need to get your accessories powered safely in your JK Jeep!

Here is the custom CNC'd bracket to relocate the mirror down about 3/4" to clear the switch panel.

The switch panel mounts overhead giving you an accessable and rugged install. Shown here with custom switch covers from OTRATTW. 

Customers Who Bought This Item Also Bought